HP X5000 G2 Скачать руководство пользователя страница 38

Страница: 38 / 179

Figure 28 Enclosure Manager unit LEDs

Table 6 Enclosure manager unit LEDs status

Status

Description

Item

The LED blinks during power-up, but then the display changes only in
response to commands from the Enclosure Manager Display.

EM display

Amber flashing/green LED off = issue. Use the CLI commands

SHOW

ENCLOSURE STATUS

and

SHOW SYSLOG EM

to determine possible

fault causes.

EM fault LED

The health LED is only green and is either on (Healthy) or off (Power
off or Faulted).

EM health LED

LEDs are off when the enclosure is powered off.

Figure 29 HP 2-port 1 GB Ethernet I/O modules LEDs

Table 7 HP 2-port 1 GB Ethernet I/O modules LEDs status

Status

Description

Item

Solid green when module health is good

Module health LED

OFF* when module has failed

Solid amber when module has failed

Module fault LED

OFF* when module health is good

*LEDs are off when enclosure is powered off.

Monitoring and troubleshooting the storage system

Содержание X5000 G2




















































































































































































Результаты поиска

Содержание X5000 G2

Отзывы:

Бренды по названию

Популярные бренды

HP X5000 G2, Руководство администратора

Результаты поиска

Содержание X5000 G2

Отзывы:

Бренды по названию

Популярные бренды