HP X5000 G2 Скачать руководство пользователя страница 16

Страница: 16 / 179

Configure iLO on the server blades:
a.

Open a web browser and log in to iLO using the address:

http://10.0.0.11

. You

are prompted to enter the user name and password. The password for the Administrator
account is located on a pull out tag on the front of the server blade.

After you have logged into iLO, HP recommends that you change the administrator
password. To do so, select

User Administration

under

Administration

in the iLO

management interface.

Configure the network as required for your environment. Select

Network

under

Administration

in the iLO management interface. You can either enable DHCP or edit the

IP address details and enter site-specific network settings. Click

Apply

to save your settings.

Repeat the process on the other server blade. Open a web browser and log in to iLO
using the address:

http://10.0.0.12

Installing the storage system

Содержание X5000 G2




















































































































































































Результаты поиска

Содержание X5000 G2

Отзывы:

Бренды по названию

Популярные бренды

HP X5000 G2, Руководство администратора

Результаты поиска

Содержание X5000 G2

Отзывы:

Бренды по названию

Популярные бренды