manualshive.com logo in svg

HP X5000 G2, Руководство администратора

Поделиться
Скачать
HP X5000 G2 Скачать руководство пользователя страница 76

Replacing the fan module

1.

Insert the replacement fan module (

Figure 60 (page 76)

).

Figure 60 Replacing the fan module

2.

Verify that the replacement component is working properly by checking the associated LED
status.

NOTE:

It should take approximately 15 seconds for the LED status to appear.

3.

Confirm that the system has resumed normal operations.

Removing and replacing the power UID button assembly

Removing the power UID button assembly

1.

Power off the system as described in

“Powering the storage system off and on” (page 60)

.

2.

Remove the enclosure from the rack as described in

“Removing the system enclosure from the

rack” (page 67)

.

3.

Remove the top back panel by pressing the panel release button and lifting the latch to slide
the top back panel off.

4.

Remove the hard drive fan module (

Figure 61 (page 76)

).

Figure 61 Removing the fan module

76

Removing and replacing hardware components

Содержание X5000 G2




















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды