HP ProLiant DL60 Gen9 Скачать руководство пользователя страница 34

Страница: 34 / 127

Setup 34

Loop the end of the hook-and-loop strap through the buckle.

When multiple hook-and-loop straps are used in the same rack, stagger the strap location, so that

the straps are adjacent to each other when viewed from top to bottom. This positioning will enable

the rack rail to slide easily in and out of the rack.

Installing the operating system

This ProLiant server does not ship with provisioning media. Everything needed to manage and install the

system software and firmware is preloaded on the server.
To operate properly, the server must have a supported operating system. Attempting to run an

unsupported operating system can cause serious and unpredictable results. For the latest information on

operating system support, see the Hewlett Packard Enterprise website

(

http://www.hpe.com/info/supportos

Failure to observe UEFI requirements for ProLiant Gen9 servers can result in errors installing the

operating system, failure to recognize boot media, and other boot failures. For more information on these

requirements, see the

HPE UEFI Requirements

on the Hewlett Packard Enterprise website

(

http://www.hpe.com/support/Gen9UEFI

To install an operating system on the server, use one of the following methods:

•

Intelligent Provisioning—For single-server deployment, updating, and provisioning capabilities.
To install an operating system on the server with Intelligent Provisioning (local or remote):

Connect the Ethernet cable between the network connector on the server and a network jack.

Press the Power On/Standby button.

During server POST, press

F10

Complete the initial Preferences and Registration portion of Intelligent Provisioning (on page

At the 1 Start screen, click

Configure and Install

To finish the installation, follow the onscreen prompts. An Internet connection is required to

update the firmware and systems software.

•

Insight Control server provisioning—For multi-server remote OS deployment, use Insight Control

server provisioning for an automated solution. For more information, see the Insight Control

documentation on the Hewlett Packard Enterprise website

(

http://www.hpe.com/info/insightcontrol/docs

Содержание ProLiant DL60 Gen9
































































































































Результаты поиска

Содержание ProLiant DL60 Gen9

Отзывы:

Похожие инструкции для ProLiant DL60 Gen9

Бренды по названию

Популярные бренды

HP ProLiant DL60 Gen9, Руководство пользователя

Результаты поиска

Содержание ProLiant DL60 Gen9

Отзывы:

Похожие инструкции для ProLiant DL60 Gen9

Бренды по названию

Популярные бренды