HP ProLiant DL120 Gen9 Скачать руководство пользователя страница 52

Страница: 52 / 130

Hardware options installation 52

Fan population guidelines

To provide sufficient airflow to the system if a fan fails, the server supports redundant fans.

Configuration

Fan bay 1 Fan bay 2 Fan bay 3 Fan bay 4 Fan bay 5

Non-redundant

Fan

Blank

Fan

Blank

Redundant*

Fan

Non-redundant (for

high efficiency
processors

exceeding 105W)

Fan

Blank

* Fan redundancy is not supported for processors exceeding 105W.

•

In the redundant fan mode:

If one fan rotor fails, the system continues to operate without redundancy. This condition is indicated
by a flashing amber Health LED.

If two fan rotors fail, the system shuts down.

The minimum fan requirement to make this server bootable is three fans.

Installing a hot-swap fan module

WARNING:

To reduce the risk of personal injury from hot surfaces, allow the drives and the

internal system components to cool before touching them.

To install the component:

Power down the server (on page

Remove all power:

Disconnect each power cord from the power source.

Disconnect each power cord from the server.

Do one of the following:

Extend the server from the rack (on page

Содержание ProLiant DL120 Gen9



































































































































Результаты поиска

Содержание ProLiant DL120 Gen9

Отзывы:

Похожие инструкции для ProLiant DL120 Gen9

Бренды по названию

Популярные бренды

HP ProLiant DL120 Gen9, Руководство пользователя

Результаты поиска

Содержание ProLiant DL120 Gen9

Отзывы:

Похожие инструкции для ProLiant DL120 Gen9

Бренды по названию

Популярные бренды