HP ProLiant DL120 Gen9 Скачать руководство пользователя страница 15

Страница: 15 / 130

Component identification 15

When a drive is configured as a part of an array and connected to a powered-up controller, the drive LEDs

indicate the condition of the drive.

Item LED

Status

Definition

Locate

Solid blue

The drive is being identified by a host application.

Flashing blue

The drive carrier firmware is being updated or requires an update.

Activity ring

Rotating green

Drive activity

Off

No drive activity

Do not remove

Solid white

Do not remove the drive. Removing the drive causes one or more of

the logical drives to fail.

Off

Removing the drive does not cause a logical drive to fail.

Drive status

Solid green

The drive is a member of one or more logical drives.

Flashing green

The drive is rebuilding or performing a RAID migration, strip size
migration, capacity expansion, or logical drive extension, or is

erasing.

Flashing

amber/green

The drive is a member of one or more logical drives and predicts

the drive will fail.

Flashing amber The drive is not configured and predicts the drive will fail.

Solid amber

The drive has failed.

Off

The drive is not configured by a RAID controller.

IMPORTANT:

The HP Dynamic Smart Array B140i Controller is only available in UEFI Boot Mode.

It cannot be enabled in Legacy BIOS Boot Mode. If the B140i controller is disabled, drives

connected to the system board Mini-SAS connectors operate in AHCI or Legacy mode. Under this

condition:

•

The drives cannot be a part of a hardware RAID or a logical drive.

•

The Locate, Drive status, and Do not remove LEDs of the affected drives are disabled.

Use BIOS/Platform Configuration (RBSU) in the UEFI System Utilities ("

HP UEFI System Utilities

" on

page

) to enable or disable the B140i controller (System Configuration

→

BIOS/Platform

Configuration (RBSU)

→

System Options

→

SATA Controller Options

→

Embedded SATA

Configuration).

Содержание ProLiant DL120 Gen9



































































































































Результаты поиска

Содержание ProLiant DL120 Gen9

Отзывы:

Похожие инструкции для ProLiant DL120 Gen9

Бренды по названию

Популярные бренды

HP ProLiant DL120 Gen9, Руководство пользователя

Результаты поиска

Содержание ProLiant DL120 Gen9

Отзывы:

Похожие инструкции для ProLiant DL120 Gen9

Бренды по названию

Популярные бренды