HP ProLiant DL120 Gen9 Скачать руководство пользователя страница 113

Страница: 113 / 130

Specifications 113

Power supply specifications

Depending on the installed options and/or the regional location where the server was purchased, the server
is configured with one of the following power supplies:

•

HP 550 W Power Supply (PN 730941-B21)

•

HP 800-W/900-W Gold AC Power Input Module (PN 744689-B21). This module is supported when

the two-bay HP RPS backplane option (PN 745813-B21) is installed.

IMPORTANT:

The HP 800-W/900-W Gold AC Power Input Module (PN 744689-B21) wattage

rating changes depending on whether one or two power input modules is installed in the server:

- Single power input module installed (non-redundant) = 900-W

- Two power input modules installed (redundant) = 800-W

For more information about the power supply features, specifications, and compatibility, see the HP website

(

http://www.hp.com/go/proliant/powersupply

CAUTION:

Check the system and power supply input ratings before powering up the server.

Hot-plug power supply calculations

For hot-plug power supply specifications and calculators to determine electrical and heat loading for the

server, see the HP Power Advisor website (

http://www.hp.com/go/hppoweradvisor

Содержание ProLiant DL120 Gen9



































































































































Результаты поиска

Содержание ProLiant DL120 Gen9

Отзывы:

Похожие инструкции для ProLiant DL120 Gen9

Бренды по названию

Популярные бренды

HP ProLiant DL120 Gen9, Руководство пользователя

Результаты поиска

Содержание ProLiant DL120 Gen9

Отзывы:

Похожие инструкции для ProLiant DL120 Gen9

Бренды по названию

Популярные бренды