![background image](http://html.mh-extra.com/html/hp/635n/635n_administrators-manual_163680044.webp)
SNMP
snmp-config:
■
Enables or disables SNMP operation on the print server.
0
disables,
1
(default) enables SNMP.
CAUTION
Disabling SNMP will disable all SNMP agents (SNMP v1, v2, v3) as well as communications with
HP Web Jetadmin. In addition, firmware upgrades through current HP downloading utilities will be disabled.
get-cmnty-name: (or get-community-name:)
■
Specifies a password that determines which SNMP GetRequests the HP Jetdirect print server will respond to. This is
optional. If a user-specified get community name is set, the print server will respond to either a user-specified
community name or the factory-default. The community name must be ASCII characters. The maximum length is 255
characters.
set-cmnty-name: (or set-community-name:)
■
Specifies a password that determines which SNMP SetRequests (control functions) the HP Jetdirect print server will
respond to. The community name of an incoming SNMP SetRequest must match the print server's “set community
name” for the print server to respond. (For additional security, you may limit configuration access through the print
server's host access list). Community names must be ASCII characters. The maximum length is 255 characters.
auth-trap: (or authentication-trap:)
■
Configures the print server to send (on) or not send (off) SNMP authentication traps. Authentication traps indicate that
an SNMP request was received, but the community name check failed. The default is “on.”
trap-dest: (or trap-destination:)
■
Enters a host's IP address into the HP Jetdirect print server's SNMP trap destination list. The command format is:
trap-dest:
ip-address
[community name] [port number]
The default community name is “public”; the default SNMP port number is “162”. The port number cannot be specified
without a community name.
If a “trap-community-name” command is followed by “trap-dest” commands, the trap community name will be assigned
to those entries unless a different community name is specified in each “trap-dest” command.
To delete the table, use “trap-dest: 0”.
If the list is empty, the print server does not send SNMP traps. The list may contain up to three entries. The default
SNMP Trap Destination List is empty. To receive SNMP traps, the systems listed on the SNMP trap destination list must
have a trap daemon to listen to those traps.
IPX/SPX
ipx-config: (or ipx/spx:)
■
Enables or disables IPX/SPX protocol operation on the print server: 0 disables, 1 (default) enables.
ipx-unit-name:
■
A user-assigned alphanumeric name assigned to the print server (31 characters maximum). By default, the name will be
NPIxxxxxx, where xxxxxx are the last six digits of the LAN hardware address.
ipx-frametype:
■
Specify the IPX frame type setting available for your print server model: AUTO (default), EN_SNAP, EN_8022,
EN_8023, EN_II.
Table 3-2
TFTP Configuration File Parameters (continued)
34
Chapter 3 TCP/IP Configuration
ENWW
Содержание 635n
