HP 6125XLG Скачать руководство пользователя страница 88

Страница: 88 / 466

Interface: 40.4.0.1 (Vlan-interface40)

Restarter state: Normal State: DR Type: Broadcast

Neighbor count of this interface: 1

Neighbor IP address GR state Last Helper exit reason

3.3.3.3 40.4.0.3 Normal None

Virtual-link Neighbor-ID -> 4.4.4.4, Neighbor-State: Full

Restarter state: Normal

Interface: 20.2.0.1 (Vlink)

Transit Area: 0.0.0.1

Neighbor IP address GR state Last Helper exit reason

4.4.4.4 20.2.0.4 Normal Reset neighbor

Table 18

Command output

Field Description

OSPF Process 1 with Router ID 1.1.1.1
Graceful Restart information

GR information for OSPF process 1 with router ID 1.1.1.1.

Graceful Restart capability

Indicates whether GR is enabled:

•

Enable(IETF)

—IETF GR is enabled.

•

Enable(Nonstandard)

—Non-IETF GR is enabled.

•

Disable

—GR is disabled.

Graceful Restart support

GR modes that the process supports (the modes are
displayed only when GR is enabled):

•

Planned and un-planned

—Supports both planned and

unplanned GR.

•

Planned only

—Supports only planned GR.

•

Partial

—Supports partial GR.

•

Global

—Supports global GR.

Helper capability

Helper capability that the process supports:

•

Enable (IETF)

—Supports IETF GR Helper capability.

•

Enable (Nonstandard)

—Supports non IETF GR Helper

capability.

•

Enable (IETF and nonstandard)

—Supports both IETF

GR Helper capability and non IETF GR Helper
capability.

•

Disable

—Does not support GR Helper capability.

Helper support

Displays policies that the Helper supports (the policies are
displayed only when Helper is enabled):

•

Strict lsa check

—The Helper supports strict LSA

checking.

•

Planned and un-planned

—The Helper supports

planned and unplanned GR.

•

Planned only

—The Helper supports only planned GR.

Содержание 6125XLG



















































































































































































































































































































































































































































































Результаты поиска

Содержание 6125XLG

Отзывы:

Похожие инструкции для 6125XLG

Бренды по названию

Популярные бренды

HP 6125XLG, Справочник по командам

Результаты поиска

Содержание 6125XLG

Отзывы:

Похожие инструкции для 6125XLG

Бренды по названию

Популярные бренды