HP 6125XLG Скачать руководство пользователя страница 56

Страница: 56 / 466

[Sysname] rip 100

[Sysname-rip-100] network 129.102.0.0

output-delay

Use

output-delay

to configure the rate at which an interface sends RIP packets.

Use

undo output-delay

to restore the default.

Syntax

output-delay

time

count

count

undo output-delay

Default

An interface sends up to three RIP packets every 20 milliseconds.

Views

RIP view

Predefined user roles

network-admin

Parameters

time

: Specifies the sending interval in the range of 10 to 100 milliseconds.

count

: Specifies the maximum number of RIP packets sent at each interval, in the range of 1 to 30.

Examples

# Configure all interfaces running RIP process 1 to send up to 10 RIP packets every 60 milliseconds.

<Sysname> system-view

[Sysname] rip 1

[Sysname-rip-1] output-delay 60 count 10

preference

Use

preference

to specify a preference for RIP routes.

Use

undo preference

to restore the default.

Syntax

preference

[

route-policy

route-policy-name

]

value

undo preference

Default

The preference of RIP routes is 100.

Views

RIP view

Predefined user roles

network-admin

Содержание 6125XLG



















































































































































































































































































































































































































































































Результаты поиска

Содержание 6125XLG

Отзывы:

Похожие инструкции для 6125XLG

Бренды по названию

Популярные бренды

HP 6125XLG, Справочник по командам

Результаты поиска

Содержание 6125XLG

Отзывы:

Похожие инструкции для 6125XLG

Бренды по названию

Популярные бренды