HP 6125XLG Скачать руководство пользователя страница 169

Страница: 169 / 466

158

protocol

: Filters routes redistributed from the specified routing protocol, which can be

bgp

direct

isis

ospf

rip

, or

static

. If no protocol is specified, the command filters all redistributed routes.

process-id

: Specifies a process by its ID in the range of 1 to 65535. This argument is available only when

the protocol is

isis

ospf

, or

rip

. The default process ID is 1.

Usage guidelines

To use an advanced ACL (with a number from 3000 to 3999) in the command, configure the ACL using

one of the following methods:

•

To deny/permit a route with the specified destination, use the

rule

[

rule-id

] {

deny

permit

}

source

sour-addr sour-wildcard

command.

•

To deny/permit a route with the specified destination and mask, use the

rule

[

rule-id

] {

deny

permit

}

ip source

sour-addr sour-wildcard

destination

dest-addr dest-wildcard

command.

The

source

keyword specifies the destination address of a route and the

destination

keyword specifies the

subnet mask of the route. The specified subnet mask must be contiguous. Otherwise, the configuration

does not take effect.

Examples

# Use ACL 2000 to filter redistributed routes.

<Sysname> system-view

[Sysname] acl number 2000

[Sysname-acl-basic-2000] rule deny source 192.168.10.0 0.0.0.255

[Sysname-acl-basic-2000] quit

[Sysname] isis 1

[Sysname-isis-1] filter-policy 2000 export

# Configure ACL 3000 to permit only route 113.0.0.0/16 to pass. Use ACL 3000 to filter redistributed
routes.

<Sysname> system-view

[Sysname] acl number 3000

[Sysname-acl-adv-3000] rule 10 permit ip source 113.0.0.0 0 destination 255.255.0.0 0

[Sysname-acl-adv-3000] rule 100 deny ip

[Sysname-acl-adv-3000] quit

[Sysname] isis 1

[Sysname-isis 1] filter-policy 3000 export

Related commands

filter-policy import

Use

filter-policy import

to configure IS-IS to filter routes calculated using received LSPs.

Use

undo filter-policy import

to restore the default.

Syntax

filter-policy

{

acl-number

prefix-list

prefix-list-name

route-policy

route-policy-name

}

import

undo filter-policy import

Default

IS-IS accepts all routes calculated using received LSPs.

Содержание 6125XLG



















































































































































































































































































































































































































































































Результаты поиска

Содержание 6125XLG

Отзывы:

Похожие инструкции для 6125XLG

Бренды по названию

Популярные бренды

HP 6125XLG, Справочник по командам

Результаты поиска

Содержание 6125XLG

Отзывы:

Похожие инструкции для 6125XLG

Бренды по названию

Популярные бренды