HP 6125XLG Скачать руководство пользователя страница 91

Страница: 91 / 466

Field Description

State

Interface state:

•

DOWN

—No protocol traffic can be sent or received on the interface.

•

Waiting

—The interface starts sending and receiving Hello packets and the

router is trying to determine the identity of the (Backup) designated router for

the network.

•

p-2-p

—The interface will send Hello packets at the interval of HelloInterval,

and try to establish an adjacency with the neighbor.

•

—The router is the designated router on the network.

•

BDR

—The router is the backup designated router on the network.

•

DROther

—The router is a DROther router on the attached network.

Cost Interface

cost.

Pri Router

priority.

DR on the interface's network segment.

BDR

BDR on the interface's network segment.

# Display detailed information about VLAN-interface 11.

<Sysname> display ospf interface Vlan-interface 11

OSPF Process 1 with Router ID 192.168.1.1

Interfaces

Interface: 172.16.0.1 (Vlan-interface11)

Cost: 1 State: DR Type: Broadcast MTU: 1500

Priority: 1

Designated Router: 172.16.0.1

Backup Designated Router: 0.0.0.0

Timers: Hello 10, Dead 40, Poll 40, Retransmit 5, Transmit Delay 1

FRR backup: enable

Table 20

Command output

Field Description

Interface

Information about the interface, such as the IP address.

Timers

OSPF timers: hello, dead, poll, retransmit, and transmit delay.

FRR backup

Indicates whether LFA calculation is enabled on an interface.

display ospf lsdb

Use

display ospf lsdb

to display OSPF LSDB information.

Содержание 6125XLG



















































































































































































































































































































































































































































































Результаты поиска

Содержание 6125XLG

Отзывы:

Похожие инструкции для 6125XLG

Бренды по названию

Популярные бренды

HP 6125XLG, Справочник по командам

Результаты поиска

Содержание 6125XLG

Отзывы:

Похожие инструкции для 6125XLG

Бренды по названию

Популярные бренды