HP 6125XLG Скачать руководство пользователя страница 108

Страница: 108 / 466

filter-policy import (OSPF view)

Use

filter-policy import

to configure OSPF to filter routes calculated using received LSAs.

Use

undo filter-policy import

to restore the default.

Syntax

filter-policy

{

acl-number

[

gateway

prefix-list-name

] |

gateway

prefix-list-name

prefix-list

prefix-list-name

[

gateway

prefix-list-name

] |

route-policy

route-policy-name

}

import

undo filter-policy import

Default

Routes calculated using received LSAs are not filtered.

Views

OSPF view

Predefined user roles

network-admin

Parameters

acl-number

: Specifies an ACL by its number in the range of 2000 to 3999 to filter inbound routes by

destination.

gateway

prefix-list-name

: Specifies an IP prefix list by its name, a case-sensitive string of 1 to 63

characters, to filter inbound routes by next hop.

prefix-list

prefix-list-name

: Specifies an IP prefix list by its name, a case-sensitive string of 1 to 63

characters, to filter inbound routes by destination.

route-policy

route-policy-name

: Specifies a routing policy by its name, a case-sensitive string of 1 to 63

characters, to filter inbound routes.

Usage guidelines

To reference an advanced ACL (with a number from 3000 to 3999) in the command or in the specified

routing policy, configure the ACL in one of the following ways:

•

To deny/permit a route with the specified destination, use the

rule

[

rule-id

] {

deny

permit

}

source

sour-addr sour-wildcard

command.

•

To deny/permit a route with the specified destination and mask, use the

rule

[

rule-id

] {

deny

permit

}

ip source

sour-addr sour-wildcard

destination

dest-addr dest-wildcard

command.

The

source

keyword specifies the destination address of a route and the

destination

keyword specifies the

subnet mask of the destination address. The specified subnet mask must be contiguous. Otherwise, the

mask configuration does not take effect.

Examples

# Use ACL 2000 to filter inbound routes.

<Sysname> system-view

[Sysname] acl number 2000

[Sysname-acl-basic-2000] rule deny source 192.168.10.0 0.0.0.255

[Sysname-acl-basic-2000] quit

[Sysname] ospf 100

[Sysname-ospf-100] filter-policy 2000 import

Содержание 6125XLG



















































































































































































































































































































































































































































































Результаты поиска

Содержание 6125XLG

Отзывы:

Похожие инструкции для 6125XLG

Бренды по названию

Популярные бренды

HP 6125XLG, Справочник по командам

Результаты поиска

Содержание 6125XLG

Отзывы:

Похожие инструкции для 6125XLG

Бренды по названию

Популярные бренды