HP 6125XLG Скачать руководство пользователя страница 335

Страница: 335 / 466

324

pr01 Vlan-interface11

Table 71

Command output

Field Description

Interface Name

Interface where the policy is applied.

Related commands

ip policy-based-route

if-match acl

Use

if-match acl

to configure an ACL match criterion.

Use

undo if-match acl

to remove the ACL match criterion.

Syntax

if-match acl

acl-number

undo if-match acl

Default

No ACL match criterion is configured.

Views

Policy node view

Predefined user roles

network-admin

Parameters

acl-number

: Specifies an ACL by its number in the range of 2000 to 3999 for a basic ACL and in the

range of 3000 to 3999 for an advanced ACL.

Examples

# Configure Node 11 of policy

to permit the packets matching ACL 2011.

<Sysname> system-view

[Sysname] policy-based-route aa permit node 11

[Sysname-pbr-aa-11] if-match acl 2011

ip policy-based-route

Use

ip policy-based-route

to configure interface PBR by applying a policy to an interface.

Use

undo ip policy-based-route

to remove the configuration.

Syntax

ip policy-based-route

policy-name

undo ip policy-based-route

Default

No policy is applied to an interface.

Содержание 6125XLG



















































































































































































































































































































































































































































































Результаты поиска

Содержание 6125XLG

Отзывы:

Похожие инструкции для 6125XLG

Бренды по названию

Популярные бренды

HP 6125XLG, Справочник по командам

Результаты поиска

Содержание 6125XLG

Отзывы:

Похожие инструкции для 6125XLG

Бренды по названию

Популярные бренды