manualshive.com logo in svg

horiba OPSA-150, Инструкция по эксплуатации

Поделиться
Скачать
horiba OPSA-150 Скачать руководство пользователя страница 110

8 Troubleshooting

98

8.4

Causes and Measures for Alarm

 

Item

Alarm

Causes

Measures

Refer

Comm
on

WARM-
UP

Waiting to be stabilized after 
the analyzer unit power ON.

No problem. (It takes 
approximately 60 minutes until 
the analyzer unit is stabilized.)

"3.2 Starting Operation" (page 
13)

CELL 
MOTOR 
ERR.

Contamination of measuring 
cell.

Clean the measuring cell.

"7.3.1 Cleaning of Measuring 
Cell" (page 84)

Failure in analyzer unit cell-
motor.

Replace the motor.

Service call

SENSOR 
COMM. 
ERR. *

Poor connection of analyzer 
unit cables.

Connect the analyzer unit 
cables properly.

Poor connection of analyzer 
unit cables or control unit, or 
faulty parts.

Connect the inside cables of the 
analyzer unit and control unit 
again.

Service call

SAMPLE 
LACK

Sample water supply is 
stopped.

Check the sample water supply 
and turn supply on.

"3.1 Preparation for Operation" 
(page 12)

Valve shut in improper 
condition.

Adjust the valves V1 to V4 in 
proper condition.

"3.1 Preparation for Operation" 
(page 12)

Clogging of piping to the 
overflow tank.

Clean the piping.

"7.4 Cleaning of Sampling Unit" 
(page 92)

Failure in float switch for no 
sample detection.

Replace the float switch.

Service call

PIO 
COMM. 
ERR. *

Communication error 
between input/output 
substrate and CPU substrate 
of control unit.

Turn the power OFF/ON. This 
may solve the problem.

Poor connection of control 
unit cables, or faulty parts.

Connect the inside cables of 
control unit again.

Service call

POWER 
ON/OFF

Power OFF by the electric 
outage.

No problem.

BATTERY 
ERR.

Backup battery for clock has 
expired.

Replace the clock backup 
battery.

Service call

LAMP 
ERR.

Contamination of measuring 
cell.

Clean the measuring cell.

"7.3.1 Cleaning of Measuring 
Cell" (page 84)

Light source is temporarily off.

Lamp may not be illuminated 
until the light source is warmed 
up. Turn the power ON/OFF and 
wait for approximately 30 
minutes as it may be restored.

Service call

Output is decreased by 
deterioration of light source.

Replace the light source.

Service call

Poor connection of control 
unit cables, or faulty detector 
or substrate

Connect the inside cables of 
control unit again.

Содержание OPSA-150
























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды