horiba LAQUA-EC1500 Скачать руководство пользователя страница 65

Страница: 65 / 80

Maintenance and Storage

■ Maintenance and Storage

This section describes the procedures for maintenance and storage of LAQUA-EC1500

benchtop meter and conductivity electrode used with the meter.

● Contact for Maintenance

Please contact your dealer for the product maintenance.

● Maintenance and Storage of the Instrument

● Cleaning the Instrument

• If the instrument is dirty, wipe it gently with a soft dry cloth. If it is difficult to remove the dirt,

wipe it gently with a cloth moistened with alcohol.

• The instrument is made of solvent resistant materials but is not resistant to all

chemicals. Do not dip the instrument in strong acid or alkali solution, or wipe it with such

solutions.

• Do not wipe the instrument with polishing powder or other abrasive compound.

● Environmental Conditions for Storage

• Temperature: 0°C to 45°C

• Humidity: under 80% relative humidity and free from condensation

● Avoid the Following Conditions:

• Dusty place

• Strong vibration

• Direct sunlight

• Corrosive gas environment

• Close to an air-conditioner

• Direct wind

Содержание LAQUA-EC1500

















































































Результаты поиска

Содержание LAQUA-EC1500

Отзывы:

Бренды по названию

Популярные бренды

horiba LAQUA-EC1500, Инструкция по эксплуатации

Результаты поиска

Содержание LAQUA-EC1500

Отзывы:

Бренды по названию

Популярные бренды