horiba LAQUA-EC1500 Скачать руководство пользователя страница 6

Страница: 6 / 80

Regulations

• Information on disposal of electrical and electronic equipment and disposal

of batteries and accumulators

The crossed out wheeled bin symbol with underbar shown on the product or accompanying

documents indicates the product requires appropriate treatment, collection and recycle for

waste electrical and electronic equipment (WEEE) under the Directive 2012/19/EU, and/or

waste batteries and accumulators under the Directive 2006/66/EC in the European Union.

The symbol might be put with one of the chemical symbols below. In this case, it satisfies

the requirements of the Directive 2006/66/EC for the object chemical. This product should not

be disposed of unsorted household waste. Your correct disposal of WEEE, waste batteries and

accumulators will contribute to reducing wasteful consumption of natural resources, and

protecting human health and the environment from potential negative effects caused by

hazardous substance in products.

Contact your supplier for information on applicable disposal methods.

• Authorised Representative in EU

HORIBA

Europe GmbH

Hans-Mess-Str.6, D-61440

Oberursel, Germany

• Authorised Representative in UK

HORIBA UK Limited

Kyoto Close Moulton Park

NN3 6FL Northampton, UK

Tel: +44 01604 542500

• FCC rules

FCC Compliance Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause undesired operation.

Responsible Party for FCC matter

HORIBA Instruments Incorporated

Head Office

9755 Research Drive

Irvine, California 92618 USA

+1 949 250 4811

Содержание LAQUA-EC1500

















































































Результаты поиска

Содержание LAQUA-EC1500

Отзывы:

Бренды по названию

Популярные бренды

horiba LAQUA-EC1500, Инструкция по эксплуатации

Результаты поиска

Содержание LAQUA-EC1500

Отзывы:

Бренды по названию

Популярные бренды