Honeywell FF-SYA14 Series Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 70

background image

107031-33-EN FR26 GLO 1101 Printed in France

43

4.

Electrical Connections

4.1

Overview

This chapter contains information about electrical installation and wiring.

IMPROPER INSTALLATION

Strictly adhere to all electrical connection instructions.

Failure to comply with these instructions could result in death or serious injury

4.2

Connector Wiring for the FF-SYA

GGGGG

GGGGG

GGGGG

GGGGG

C2 light curtains

All FF-SYA

qqqqq

C2 light curtains have two plastic quick-disconnect connectors. Emitter units and receiver units use the

same connector. The figure below illustrates a rear view of the connector (crimped contacts inserted this side). Both emitter
and receiver use the same connector type and both connectors use the same type of crimped contacts.

Figure 4-1 View of customer quick-disconnect Connector (Hirschmann N6RFF connector type)

1

2

3

4

5

6

Rear View of customer Connector

(crimped contacts inserted this side)

2

1

6

5

4

3

Front View of customer Connector

(Do NOT insert crimped contact from this side)

Ensure the following tools are available when wiring the quick-disconnect connector:

•

A set of wire strippers.

•

A flat-head screwdriver.

•

A regular crimping tool.

The crimping tool can also be ordered at Honeywell under the reference FF-SBZCRIMP. Additional crimping contacts may be
ordered under the reference FF-SBZ172115 (100 pieces)

Cross sectional area of the cables: minimum 0,5 mm² / AWG 21, maximum 1,5 mm² / AWG 16 stranded wire.
Packing Gland and recommended cable diameters to guarantee the IP 65/NEMA 4, 13 sealing: PG11 allows use of cable
diameters from 6,5 mm to 10,5 mm (0.25 in to 0.41 in)

Install socket contacts into connector as follows:

1.

Strip about 8 mm (0,3 in) of insulation from the wire end.

2.

Using a crimping tool, crimp the socket contact onto the wire.

3.

Push the socket contact into the correct slot in the connector. Tabs on the sides of the socket contact will expand into
slots and hold the socket contact in place when properly seated.

Remove a socket contact from the connector as follows:

1.

Remove the cover from the plug.

2.

Unscrew the contact receptacle.

3.

Using the removal tool, slide over socket contact and push until the spring releases the socket contact; remove socket
contact.

Change the position of the plug as follows:

1.

Unscrew the socket contact receptacle.

2.

Pull out and rotate the receptacle to change the position of the polarising slot

3.

Install the socket contact receptacle.

F

SYA6

9

F

SYA7

0

«
...
45
46
47
48
49
...
»

Содержание FF-SYA14 Series







































































Отзывы:

Нет отзывов

Похожие инструкции для FF-SYA14 Series

Бренд: Malmet Страницы: 14

Бренд: Zempire Страницы: 2

Бренд: NEILPRYDE Страницы: 53

Бренд: JAC Страницы: 103

Бренд: 3Disc Страницы: 12

Бренд: Abbott Страницы: 2

FreeStyle Libre

Бренд: Abbott Страницы: 3

Бренд: abc Страницы: 8

Бренд: Parker Research Corp Страницы: 4

Бренд: Eastwood Страницы: 20

Бренд: Daihan Scientific Страницы: 43

Бренд: Ecler Страницы: 108

Бренд: R&S Страницы: 121

Бренд: KaVo Страницы: 4

ORTHOPANTOMOGRAPH OP 3D

Бренд: KaVo Страницы: 40

KEY Laser III 1243

Бренд: KaVo Страницы: 103

EXTRAmatic 9040

Бренд: KaVo Страницы: 56

ESTETICA E70 Vision

Бренд: KaVo Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды