Honeywell CGW-MB Скачать руководство пользователя страница 57

Страница: 57 / 187

CGW-MB Installation and Users’ Manual | P/N:LS10248-000HW-E | REV.G | JUL/31/2022

CGW-MB Control Features

Modbus Communications

For NOTIFIER UL

Table 7.13: Zone Commands

Table 7.9: Point Commands

Command

Value

Holding Register

Acknowledge Point

0x0200

Use Device/Module

Holding Register

Address

Acknowledge Block

0x0300

Enable

0x0400

Disable

0x0500

Activate*

0x0800

Deactivate*

0x0900

Acknowledge Trouble

0x0b00

Acknowledge Alarm

0x0c00

Acknowledge CO and Gas
Alarm

0x0d00

Table 7.10: Zone Commands

Command

Value

Holding Register

Enable

0x0400

Use Device/Module Holding
Register Address

Disable

0x0500

Activate*

0x0800

Deactivate*

0x0900

Table 7.11: Node Commands

Command

Value

Holding Register

Reset

0x0001

20001

Silence

0x0002

Table 7.12: Point Commands

Command

Value

Holding Register

Acknowledge

0x0100

Use Device/Module Holding Register

Address

Disable

0x0200

Enable

0x0400

Activate

0x0800

Deactivate

0x1000

Command

Value

Holding Register

Disable

0x0200

Use Zone Holding Register Address

Enable

0x0400

Activate

0x0800

Deactivate

0x1000

Activate and Deactivate work only for output-controlled modules like

control and relay.
Different panels support different zone types. Refer to

Table 7.7, “Zone

Command Availability by Panel”

for information about zone types

supported.

Содержание CGW-MB




























































































































































































Результаты поиска

Содержание CGW-MB

Отзывы:

Honeywell CGW-MB, Инструкция по установке и эксплуатации, Страница: 57 / 187

Результаты поиска

Содержание CGW-MB

Отзывы: