Honeywell CGW-MB Скачать руководство пользователя страница 158

Страница: 158 / 187

CGW-MB Installation and Users’ Manual | P/N:LS10248-000HW-E | REV.G | JUL/31/2022

157

FireWarden Panels

Connecting to the Panels

C.6.5 To Use Panel’s Printer Port Connection

Some FireWarden panels support data transfer through their printer terminal.

1. On the CLSS Gateway mainboard Side

• Connect the serial cable into the RS-232 port of the CLSS Gateway mainboard.
The RS-232 port is labeled as 6 in the

Figure C.15

2. On the Panel Side

Connect the serial cable in the DB9 serial port of the ANN-S/PG module on the panel.

3. Power Connection

On the CLSS Gateway mainboard Side
• Connect to the 24V DC external power supply.
• Switch the S7 Switch next to the RS-232 port towards

NUP_OUT

Figure C.14: The S7 Switch

On the Panel Side
Connect the power cable to a 24V DC external power source or the panel’s power

supply.

NOTE:

Compatible CGW-MB firmware versions: 2.1.11.16 and above

CAUTION: ENSURE THAT ONLY THE ANN-S/PG IS CONNECTED AND NOT THE CGW-MB. ONLY ONE OF

THESE TWO CAN BE CONNECTED. BOTH OF THEM MUST NOT BE CONNECTED TOGETHER.

Содержание CGW-MB




























































































































































































Результаты поиска

Содержание CGW-MB

Отзывы:

Honeywell CGW-MB, Инструкция по установке и эксплуатации, Страница: 158 / 187

Результаты поиска

Содержание CGW-MB

Отзывы: