Honeywell CGW-MB Скачать руководство пользователя страница 146

Страница: 146 / 187

CGW-MB Installation and Users’ Manual | P/N:LS10248-000HW-E | REV.G | JUL/31/2022

145

ESSER Panels

Connecting to the Panels

C.4.5 To Use an RS232 Connection for Events

Using an SEI1 Card

Connect to the RS232 module (772386) as below:

1. On the CLSS Gateway mainboard Side

Connect the RS232 cable with pre-formed connector to the RS232 port of the CLSS

Gateway mainboard board.

Tip

: The RS232 port in the CLSS Gateway mainboard board is labeled as 6 in the

Figure C.2

2. On the Panel Side

• IQ8: Connecting through a Serial Interface Card

IQ8: Connecting through a Serial Interface Card

• Connect the White wire to the RxD+ pin.
• Connect the Green wire to the GND pin.
• Connect the Brown wire to the TxD+ pin.

Figure C.7: Wiring Diagram: RS232 Connection for an IQ8 Panel

3. Power Connection

•

For FlexES Panels

Using a power cable, the CLSS Gateway mainboard can connect to the 24V DC power

supply module of the FlexES panel.

On the CLSS Gateway mainboard Side

• Connect the +ve wire to the +ve pin of the power supply port.
• Connect the -ve wire to the -ve pin of the power supply port.

NOTE:

Use the details given on the power supply module of the panel.

NOTE:

The panel’s power supply to the CLSS Gateway mainboard must be 24V DC

power.

Содержание CGW-MB




























































































































































































Результаты поиска

Содержание CGW-MB

Отзывы:

Honeywell CGW-MB, Инструкция по установке и эксплуатации, Страница: 146 / 187

Результаты поиска

Содержание CGW-MB

Отзывы: