Honeywell AlarmNet 7810iR Скачать руководство пользователя страница 60

Страница: 60 / 64

7810iR Internet Communication Module Installation and Setup Guide

7-8

Keypad Test

The Keypad Test is not applicable for 7810iR.

Touch Screen Calibration

Calibrate the touch screen as follows:

Action Screen

Display

1. Press the

Diagnostics

button on the

"Advanced Setup" menu screen. The
"Diagnostics/Test" screen is displayed.

2. Begin the Touch Screen calibration from the
"Diagnostics/Tests" screen by pressing the

Calibrate

button. When the

Calibrate

button is

pressed, the

Touch Screen Calibration

screen is displayed.

Within the

Touch Screen Calibration

screen

you are asked to

Press the center of the box

in upper left corner.

Press the center of the

square.

When this square is touched, the

Touch

Screen Calibration

screen displays

Next

press the center of the box in the upper
right corner.

Содержание AlarmNet 7810iR

































































Результаты поиска

Содержание AlarmNet 7810iR

Отзывы:

Honeywell AlarmNet 7810iR, Руководство по установке и настройке, Страница: 60 / 64

Результаты поиска

Содержание AlarmNet 7810iR

Отзывы: