Honeywell AlarmNet 7810iR Скачать руководство пользователя страница 47

Страница: 47 / 64

Section 6: Message Formats

6-15

202

Low

CO2

Super.-Low

CO2-#

203

Gate Valve Sensor

Super.-Gate Valve-#

204

Low Water Level

Super.-Low Water Level-#

205

Pump

Activated

Super.-Pump

Activation-#

206

Pump

Failure

Super.-Pump

Failure-#

System Troubles

300

System

Trouble

Trouble-System

Trouble

301

Ac Loss

Trouble-Ac Power

302

Low System Batt

Trouble-Low Battery (AC is lost, battery is getting low)

303

RAM Checksum Bad

Trouble-Bad RAM Checksum (Restore Not Applicable)

304

ROM Checksum Bad

Trouble-Bad ROM Checksum (Restore Not Applicable)

305

System Reset

Trouble-System Reset (Restore Not Applicable)

306 Panel Prog Change

Trouble-Programming Changed (Restore Not
Applicable)

307 Self-Test Failure

Trouble-Self Test Failure

308 System Shutdown

Trouble-System Shutdown

309 Battery Test Fail

Trouble-Battery Test Failure (Battery failed at test
interval)

310

Ground Fault

Trouble-Ground Fault-#

311

Battery

Missing

Trouble-Battery

Missing

312

Power Supply Over current

Trouble-Pwr. Supp. Overcur.-#

313 Engineer Reset

Status-Engineer Reset – User # (Restore Not
Applicable)

Sounder/Relay Troubles

320

Sounder / Relay

Trouble-Sounder/Relay-#

321

Bell 1

Trouble-Bell/Siren #1 (Event An Restore)

322

Bell 2

Trouble-Bell/Siren #2 (Event an Restore)

323

Alarm

Relay

Trouble-Alarm

Relay

324

Trouble

Relay

Trouble-Trouble

Relay

325

Reversing Relay

Trouble-Reversing Relay

326

Notification Appliance Ckt. # 3 Trouble-Notification Appl. Ckt#3

327

Notification Appliance Ckt. # 4 Trouble-Notification Appl. Ckt#4

System Peripheral Troubles

330 System

Peripheral

Trouble-Sys.

Peripheral-#

331

Polling Loop Open

Trouble-Polling Loop Open

332

Polling Loop Short

Trouble-Polling Loop Short

333

Exp. Module Failure

Trouble-Exp. Module Fail-#

334

Repeater Failure

Trouble-Repeater Failure-#

335

Local Printer Paper Out

Trouble-Printer Paper Out

Содержание AlarmNet 7810iR

































































Результаты поиска

Содержание AlarmNet 7810iR

Отзывы:

Honeywell AlarmNet 7810iR, Руководство по установке и настройке, Страница: 47 / 64

Результаты поиска

Содержание AlarmNet 7810iR

Отзывы: