Honda NHSO aeroBO 1983 Скачать руководство пользователя страница 15

Страница: 15 / 184

HONDA

NHSO

Tighten the oil pump attaching bolt securely.

Connect the oil outlet line.

Install the starter motor (Page 15·15).

Install the engine (Page 5-4).

NOTE:

After installation, perform the following inspec·

tions and adjustment:

•

Control cable adjustment (Page 2-4)

•

Oil

pump bleeding.

•

Check for oil leaks.

OIL PUMP BLEEDING

CAUTION:

•

Air in the oil system will block or restrict
oil flow and may result in severe engine dam

age.

•

Bleed air from the oil inlet line first, then

bleed air from the oil outlet line.

01 L I N LET LI NE/01 L PUMP

CAUTION:

Bleed  air  from  the  oil  lines  whenever  the  oil
lines  or  pump  have  been  removed  or  there  is
air in the  oil lines.

Fill the oil tank with recommended oil.

Place a

shop towel around the oil pump.

Disconnect the oil inlet line from the oil pump.

Fill the oil pump with oil by squirting clean oil

through the joint (about 3

cc).

Fill the oil line with oil and connect it to the joint of

the oil pump.

After installation, make sure there is no air in the oil

inlet line.

CAUTION:

Bleed air from the oil outlet line after bleeding

the oil inlet line and oil pump.

Date of Issue: May, 1983

LUBRICATION

OIL OUTLET LINE

1 7

2 - 3

Содержание NHSO aeroBO 1983

























































































































































































Результаты поиска

Содержание NHSO aeroBO 1983

Отзывы:

Похожие инструкции для NHSO aeroBO 1983

Бренды по названию

Популярные бренды

Honda NHSO aeroBO 1983, Руководство по ремонту

Результаты поиска

Содержание NHSO aeroBO 1983

Отзывы:

Похожие инструкции для NHSO aeroBO 1983

Бренды по названию

Популярные бренды