Honda DS-2CC102P(N)-IRT Скачать руководство пользователя страница 68

Страница: 68 / 115

SERVICING YOUR GENERATOR

Battery Charging

The battery is rated at 11.2 Ah (ampere-hours). Charging current should
equal 10% of the battery’s ampere-hour rating. A battery charger
should be used that can be adjusted to deliver 1.1 amps.

1. Connect the battery charger following the manufacturer’s

instructions.

2. Charge the battery 5–10 hours.
3. Clean the outside of the battery and the battery compartment with a

solution of baking soda and water.

Battery Installation

1. Install the battery into the generator.
2. Connect the battery positive (+) cable to the battery positive (+)

terminal first, and tighten the bolt securely.

3. Slide the battery boot over the positive (+) cable and terminal.
4. Connect the battery negative (–) cable to the battery negative (–)

terminal, and tighten the bolt securely.

5. Install the battery strap.
6. Install the battery maintenance cover in the reverse order of removal

(see page 64).
Never operate the generator without the battery maintenance cover
in place, as poor engine and generator performance will result.

The battery gives off explosive
hydrogen gas during normal
operation.

A spark or flame can cause the
battery to explode with enough force
to kill or seriously hurt you.

Wear protective clothing and a face
shield, or have a skilled mechanic
perform the battery maintenance.

31Z37613.book 66 ページ２０１５年１２月２日　水曜日　午前１０時４５分

Содержание DS-2CC102P(N)-IRT




















































































































Результаты поиска

Содержание DS-2CC102P(N)-IRT

Отзывы:

Похожие инструкции для DS-2CC102P(N)-IRT

Бренды по названию

Популярные бренды

Honda DS-2CC102P(N)-IRT, Руководство пользователя

Результаты поиска

Содержание DS-2CC102P(N)-IRT

Отзывы:

Похожие инструкции для DS-2CC102P(N)-IRT

Бренды по названию

Популярные бренды