Honda DS-2CC102P(N)-IRT Скачать руководство пользователя страница 99

Страница: 99 / 115

ASSEMBLY

Wheel Kit Installation

Do not operate the generator without the wheel kit installed. The wheel
kit provides air space between the ground and the generator air intake.

If the wheel kit is not installed, it may be possible for dirt and debris to
be drawn into the generator air intake, possibly causing generator
damage. Always operate the generator with the wheel kit installed.

1. Install the two stands on the under frame using four 8×20 mm

flange bolts.

2. Install the two wheels on the axle using the 20 mm washers and

4.0×28 mm cotter pins. After installing the split pins, bend the pins
to ensure that the wheels are secured to the axle.

3. Install the axle assembly on the generator using four 8×20 mm

flange bolts.

TORQUE:

11–16 lbf·ft (15–22 N·m, 1.5–2.2 kgf·m)

STAND

8×20 mm
FLANGE BOLT (4)

4.0×28 mm
COTTER PIN (2)

AXLE

WHEEL (2)

8×20 mm
FLANGE BOLT (4)

20 mm WASHER (2)

SHORTER

31Z37613.book 97 ページ２０１５年１２月２日　水曜日　午前１０時４５分

Содержание DS-2CC102P(N)-IRT




















































































































Результаты поиска

Содержание DS-2CC102P(N)-IRT

Отзывы:

Похожие инструкции для DS-2CC102P(N)-IRT

Бренды по названию

Популярные бренды

Honda DS-2CC102P(N)-IRT, Руководство пользователя

Результаты поиска

Содержание DS-2CC102P(N)-IRT

Отзывы:

Похожие инструкции для DS-2CC102P(N)-IRT

Бренды по названию

Популярные бренды