Honda DS-2CC102P(N)-IRT Скачать руководство пользователя страница 29

Страница: 29 / 115

BEFORE OPERATION

Check the Engine

• Before each use, look around and underneath the engine for signs of

oil or gasoline leaks.

• Check the engine oil level (see page 55). A low engine oil level will

cause the Oil Alert system to shut down the engine.

• Check the air filters (see page 58). Dirty air filters will restrict air flow

to the fuel system, reducing engine and generator performance.

• Check the fuel level (see page 53). Starting with a full tank will help

to eliminate or reduce operating interruptions for refueling.

Check the GFCI

Check the GFCI operation (see page 35) after starting the engine.

Battery Maintenance Cover

Never operate the generator without the battery maintenance cover in
place, as poor engine and generator performance will result.

BATTERY MAINTENANCE COVER

31Z37613.book 27 ページ２０１５年１２月３日　木曜日　午前９時３３分

Содержание DS-2CC102P(N)-IRT




















































































































Результаты поиска

Содержание DS-2CC102P(N)-IRT

Отзывы:

Похожие инструкции для DS-2CC102P(N)-IRT

Бренды по названию

Популярные бренды

Honda DS-2CC102P(N)-IRT, Руководство пользователя

Результаты поиска

Содержание DS-2CC102P(N)-IRT

Отзывы:

Похожие инструкции для DS-2CC102P(N)-IRT

Бренды по названию

Популярные бренды