Honda DS-2CC102P(N)-IRT Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 115

background image

53

SERVICING YOUR GENERATOR

REFUELING

With the engine stopped, check the fuel level gauge. Refill the fuel tank
if the fuel level is low.

Fuel can damage paint and plastic. Be careful not to spill fuel when
filling your fuel tank. Damage caused by spilled fuel is not covered
under the

Distributor’s Limited Warranty.

Refuel in a well-ventilated area before starting the engine. If the engine
has been running, allow it to cool. Refuel carefully to avoid spilling fuel.
Do not fill the fuel tank above the upper level mark (red) on the fuel
strainer.

Never refuel the engine inside a building where gasoline fumes may
reach flames or sparks. Keep gasoline away from appliance pilot lights,
barbecues, electric appliances, power tools, etc.

Spilled fuel is not only a fire hazard, it causes environmental damage.
Wipe up spills immediately.

Gasoline is highly flammable and
explosive.

You can be burned or seriously
injured when handling fuel.

• Stop the engine and keep heat,

sparks, and flame away when
refueling.

• Handle fuel only outdoors.
• Wipe up spills immediately.

31Z37613.book 53 ページ２０１５年１２月２日　水曜日　午前１０時４５分

«
...
53
54
55
56
57
...
»

Содержание DS-2CC102P(N)-IRT




















































































































Отзывы:

Нет отзывов

Похожие инструкции для DS-2CC102P(N)-IRT

Бренд: HQ Страницы: 76

Бренд: R&S Страницы: 40

Бренд: Danfoss Страницы: 7

Бренд: Danfoss Страницы: 16

VLT 2800 Series

Бренд: Danfoss Страницы: 34

VLT AutomationDrive FC 300

Бренд: Danfoss Страницы: 60

VLT 5000 Series

Бренд: Danfoss Страницы: 63

Бренд: NAD Страницы: 3

Бренд: Goobay Страницы: 24

Бренд: Soundfield Страницы: 13

Бренд: Ace Plus Страницы: 9

Бренд: Briggs & Stratton Страницы: 36

IFS MC250-4T Series

Бренд: Interlogix Страницы: 23

Бренд: M-Audio Страницы: 8

SinePower SP150

Бренд: Waeco Страницы: 96

Бренд: C&C TECHNIC TAIWAN CO., LTD. Страницы: 20

Бренд: Ledco Страницы: 4

Бренд: TC Communications Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды