background image

48

OPERATION

STANDBY POWER

Connections to a Building’s Electrical System

Connections for standby power to a building's electrical system must 
be made by a qualified electrician. The connection must isolate the 
generator power from utility power, and must comply with all 
applicable laws and electrical codes.

In some areas, generators are required by law to be registered with 
local utility companies. Check local regulations for proper registration 
and use procedures.

System Ground

This generator has a system ground that connects generator frame 
components to ground terminals in the AC output receptacles. The 
system ground is not connected to the AC neutral wire.

Improper connections to a building’s 
electrical system can allow current 
from the generator to backfeed into 
the utility lines.

Such backfeed may electrocute 
utility company workers or others 
who contact the lines during a 
power outage, and the generator 
may explode, burn, or cause fires 
when utility power is restored.

Consult the utility company or a 
qualified electrician prior to making 
any power connections.

31Z37613.book  48 ページ  2015年12月2日 水曜日 午前10時45分

Содержание DS-2CC102P(N)-IRT




















































































































Отзывы: