Honda DS-2CC102P(N)-IRT Скачать руководство пользователя

Страница: 38 / 115

OPERATION

1. Unplug all tools and appliances from the generator.

2. Start the engine (see page 29).

When the GFCI is operating normally, the indicator will
continuously light green.

Light order:
(red) Blink once

→

(green) Light once

→

(red) Blink once

→

(green) Lights continuously

• If the green indicator does not light on, press the RESET button.
• If the red indicator starts to blink continuously, contact an

authorized Honda generator dealer.

3. Press the TEST button:

• The RESET button will pop out and the green indicator will go off.
• If the GFCI does not function as described, contact an authorized

Honda generator dealer.

RESET BUTTON

INDICATOR

TEST BUTTON

31Z37613.book 36 ページ２０１５年１２月１７日　木曜日　午後８時５８分

Содержание DS-2CC102P(N)-IRT




















































































































Результаты поиска

Содержание DS-2CC102P(N)-IRT

Отзывы:

Похожие инструкции для DS-2CC102P(N)-IRT

Бренды по названию

Популярные бренды

Honda DS-2CC102P(N)-IRT, Руководство пользователя

Результаты поиска

Содержание DS-2CC102P(N)-IRT

Отзывы:

Похожие инструкции для DS-2CC102P(N)-IRT

Бренды по названию

Популярные бренды