Honda DS-2CC102P(N)-IRT Скачать руководство пользователя страница 60

Страница: 60 / 115

SERVICING YOUR GENERATOR

AIR CLEANER SERVICE

1. Open the left maintenance cover by turning its latch

counterclockwise.

2. Unsnap the air cleaner cover clips; remove the air cleaner cover.

3. Foam air filter:

a. Remove the foam air filter from the air cleaner cover.
b. Check the foam air filter to be sure it is clean and in good

condition.
If the foam air filter is dirty, clean it as described on page 59.
Replace the foam air filter if it is damaged.

c. Reinstall the foam air filter in the air cleaner cover.

4. Paper air filter:

a. Remove the guide.
b. If the paper air filter is dirty, replace it with a new one.

Do not clean the paper air filter.

5. Reinstall the guide and the air cleaner cover.

6. Close the left maintenance cover.

Operating the engine without the air filters or with a damaged air filters
will allow dirt to enter the engine, causing rapid engine wear. This type
of damage is not covered by the

Distributor’s Limited Warranty.

PAPER AIR FILTER

AIR CLEANER COVER

CLIP

GUIDE

FOAM AIR FILTER

31Z37613.book 58 ページ２０１５年１２月２日　水曜日　午前１０時４５分

Содержание DS-2CC102P(N)-IRT




















































































































Результаты поиска

Содержание DS-2CC102P(N)-IRT

Отзывы:

Похожие инструкции для DS-2CC102P(N)-IRT

Бренды по названию

Популярные бренды

Honda DS-2CC102P(N)-IRT, Руководство пользователя

Результаты поиска

Содержание DS-2CC102P(N)-IRT

Отзывы:

Похожие инструкции для DS-2CC102P(N)-IRT

Бренды по названию

Популярные бренды