Honda DS-2CC102P(N)-IRT Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 115

background image

39

OPERATION

3. Plug in the appliance.

Most motorized appliances
require more than their rated
wattage for startup.

4. Turn on the appliance.

If the generator is overloaded, or if there is a short circuit in a
connected appliance, or if the inverter is overheated, the red
OVERLOAD ALARM indicator will come ON. The red OVERLOAD
ALARM indicator will stay ON and, after about five seconds, current to
the connected appliance(s) will shut off, and the green OUTPUT
indicator will go OFF. Stop the engine and investigate the problem.

Determine if the cause is a short circuit in a connected appliance, an
overload, or an overheated inverter. Correct the problem and restart the
generator.

Before connecting an appliance to the generator, make sure that it is
in good order and that its electrical rating does not exceed that of the
generator. Then start the generator and connect the appliance power
cord.

When an electric motor is started, the red OVERLOAD ALARM
indicator may come on. This is normal if the red OVERLOAD ALARM
indicator goes OFF after about five seconds. If the red OVERLOAD
ALARM indicator stays ON, consult an authorized Honda generator
dealer.

PLUG

31Z37613.book 39 ページ２０１５年１２月１５日　火曜日　午後６時７分

«
...
39
40
41
42
43
...
»

Содержание DS-2CC102P(N)-IRT




















































































































Отзывы:

Нет отзывов

Похожие инструкции для DS-2CC102P(N)-IRT

Бренд: OST Страницы: 2

Power Inverter PNVS4

Бренд: Pyle Страницы: 1

Бренд: B&K Страницы: 2

Бренд: York Страницы: 41

Бренд: Actox Страницы: 36

DA1-34072FB-B20C

Бренд: Eaton Страницы: 16

Бренд: Profi Power Страницы: 17

Бренд: tams elektronik Страницы: 28

Бренд: Teleste Страницы: 44

Бренд: HQ Power Страницы: 8

Digital plus Silver 10331

Бренд: Lenz Elektronik Страницы: 13

Бренд: Kogan Страницы: 3

Бренд: Kubota Страницы: 166

Бренд: Nokia Страницы: 6

Freedom SW 815-2012

Бренд: Xantrex Страницы: 78

Бренд: M-system Страницы: 2

Бренд: M-system Страницы: 8

midiman Flying Calf D/A

Бренд: M-Audio Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды