Honda BF100A Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 174

background image

36

CONTROLS AND FEATURES (T type)

Manual Relief Valve

If the power trim/tilt switch will not
tilt the outboard motor, the outboard
motor can be manually tilted up or
down by opening the manual relief
valve. To tilt the outboard motor
manually, turn the manual relief valve
under the left stern bracket no more
than 1 or 2 turns counterclockwise
using a screwdriver.

After tilting the outboard motor, turn
the manual relief valve clockwise
securely.

Check that no person is under the
outboard motor before carrying out
this operation because if the manual
relief valve is loosened (turned
counterclockwise) when the

outboard motor is tilted up, the
outboard motor will suddenly tilt
down.

The manual relief valve must be
tightened securely before operating
the outboard motor or the outboard
motor could tilt up when operating in
reverse.

MANUAL RELIEF VALVE

POWER
(To fix)

MANUAL
(To release)

<;DQQMࡍ࡯ࠫ㧞㧜㧝㧟ᐕ㧝㧜᦬㧝㧤ᣣޓ㊄ᦐᣣޓඦᓟ㧞ᤨ㧟㧟ಽ

«
...
35
36
37
38
39
...
»

Содержание BF100A















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BF100A

Бренд: ASROCK Страницы: 39

Бренд: JETWAY Страницы: 46

Бренд: Texas Instruments Страницы: 17

Бренд: Aaeon Страницы: 120

Бренд: Vox Страницы: 23

Бренд: XMOS Страницы: 20

Бренд: Intel Страницы: 76

H470 AORUS PRO AX

Бренд: Gigabyte Страницы: 52

Бренд: Aaeon Страницы: 56

Бренд: SOYO Страницы: 94

Бренд: Gigabyte Страницы: 60

Бренд: Pegatron Страницы: 30

Бренд: Lite-on Tech Страницы: 49

Бренд: ON Semiconductor Страницы: 5

Бренд: BCM Страницы: 59

Бренд: Commell Страницы: 53

Бренд: JETWAY Страницы: 47

Бренд: Gigabyte Страницы: 75

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды