manualshive.com logo in svg

Honda BF100A, Руководство пользователя

Поделиться
Скачать
Honda BF100A Скачать руководство пользователя страница 136

135

MAINTENANCE

<Battery Cleaning>

1. Disconnect the battery cable at the 

battery negative (–) terminal, then 
at the battery positive (+) terminal. 

2. Remove the battery and clean the 

battery terminals and battery cable 
terminals with a wire brush or sand 
paper.

Clean the battery with a solution of 
baking soda and warm water, 
taking care not to get the solution 
or water in the battery cells. Dry 
the battery thoroughly.

3. Connect the battery positive (+) 

cable to the battery positive (+) 
terminal, then the battery negative 
(–) cable to the battery negative (–) 
terminal. Tighten the bolts and nuts 
securely. Coat the battery 

terminals with grease.

When disconnecting the battery 
cable, be sure to disconnect at the 
battery negative (–) terminal first. 
To connect, connect at the positive 
(+) terminal first, then at the 
negative (–) terminal. Never dis/
connect the battery cable in the 
reverse order, or it causes a short 
circuit when a tool contacts the 
terminals.

NEGATIVE (–) 
TERMINAL

POSITIVE (+) 
TERMINAL

BLACK

RED

<;DQQMࡍ࡯ࠫ㧞㧜㧝㧟ᐕ㧝㧜᦬㧝㧤ᣣޓ㊄ᦐᣣޓඦᓟ㧞ᤨ㧟㧟ಽ

Содержание BF100A















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды