manualshive.com logo in svg

Honda BF100A, Руководство пользователя

Поделиться
Скачать
Honda BF100A Скачать руководство пользователя страница 61

60

PRE-OPERATION CHECKS

SAE 10W-30 is recommended for 
general use.

<Inspection and Refilling>

1. Position the outboard motor 

vertically, and remove the engine 
cover.

2. Remove the oil level dipstick and 

wipe with a clean rag.

3. Reinsert the dipstick all the way in, 

and then pull it out and read the 
level. If near or below the lower 
level mark, remove the oil filler cap 
and fill to the upper level mark 
with the recommended oil. Tighten 
the oil filler cap and install the 
dipstick securely. Do not 
overtighten.

When the engine oil is contaminated 
or discolored, replace with the fresh 
engine oil (see page 128 for 
replacement interval and procedure).

AMBIENT TEMPERATURE

OIL LEVEL DIPSTICK

UPPER 
LEVEL 
MARK

LOWER 
LEVEL 
MARK

<;DQQMࡍ࡯ࠫ㧞㧜㧝㧟ᐕ㧝㧜᦬㧝㧤ᣣޓ㊄ᦐᣣޓඦᓟ㧞ᤨ㧟㧟ಽ

Содержание BF100A















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды