manualshive.com logo in svg

Honda BF100A, Руководство пользователя

Поделиться
Скачать
Honda BF100A Скачать руководство пользователя страница 155

154

15. TROUBLESHOOTING

WARNING SYSTEM COMES ON

SYMPTOM

POSSIBLE CAUSE

REMEDY

Overheat warning system comes on:

• Overheat indicator comes on.
• Overheat warning buzzer sounds.
• Engine speed decreases and stops at last.
• Engine speed cannot be increased by opening the throttle.
• Engine will stop in 20 seconds after engine speed is limited.

Cooling water intake port clogged.

Clean the cooling water intake port.

Spark plugs have improper heat range.

Replace the spark plugs

(see pages 130 – 133).

• Faulty water pump.
• Thermostat clogged.
• Faulty thermostat.
• Cooling water passage clogged.
• Exhaust gas invades cooling system.

Consult with an authorized
Honda outboard motor dealer.

Oil pressure warning system comes on:

• Oil pressure indicator does not come on.
• Oil pressure warning buzzer sounds.
• Engine speed decreases.
• Engine speed cannot be increased by opening the throttle.

Shortage of engine oil

Add engine oil to the specified
level (see page 59).

Improper engine oil is used.

Change the engine oil
(see page 128).

<;DQQMࡍ࡯ࠫ㧞㧜㧝㧟ᐕ㧝㧜᦬㧝㧤ᣣޓ㊄ᦐᣣޓඦᓟ㧞ᤨ㧟㧟ಽ

Содержание BF100A















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды