manualshive.com logo in svg

Honda BF100A, Руководство пользователя

Поделиться
Скачать
Honda BF100A Скачать руководство пользователя страница 139

138

MAINTENANCE

Water Separator

Water separator is located near by the 
engine cover fixing lever of the boat 
side. Water accumulation in the water 
separator can cause loss of power or 
hard starting. Check the water 
separator periodically. Clean it or 
consult with an authorized Honda 
outboard motor dealer for cleaning.

Gasoline is extremely flammable, 
and gasoline vapor can explode, 
causing serious injury or death. Do 
not smoke or allow flames or 
sparks in your working area. 
KEEP OUT OF REACH OF 
CHILDREN.

• Always work in a well-ventilated 

area. 

• Be sure that any fuel drained 

from the outboard motor is 
stored in a safe container.

• Be careful not to spill fuel when 

cleaning the water separator. 
Spilled fuel or fuel vapor may 
ignite. If any fuel is spilled, make 
sure the area is dry before 
starting the engine.

<Cleaning>

1. Remove the engine cover (see page 

59).

2. Remove the suspension strap from 

the water separator bracket, then 
remove the strap from the separator 
assembly.

During removal of the water 
separator assembly, take care not 
to damage the wire harness with 
the water separator bracket.

WATER SEPARATOR

FUEL TUBES

SCREWS (3)

SUSPENSION 
STRAP

WATER SEPARATOR BRACKET

WATER 
SEPARATOR

<;DQQMࡍ࡯ࠫ㧞㧜㧝㧟ᐕ㧝㧜᦬㧝㧤ᣣޓ㊄ᦐᣣޓඦᓟ㧞ᤨ㧟㧟ಽ

Содержание BF100A















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды