Honda BF100A Скачать руководство пользователя страница 71

Страница: 71 / 174

7. STARTING THE ENGINE

Fuel Line Connection

Gasoline is extremely flammable,
and gasoline vapor can explode,
causing serious injury or death.

• Be careful not to spill fuel.

Spilled fuel or fuel vapor may
ignite. If any fuel is spilled, make
sure the area is dry before
starting, storing or transporting
the engine.

• Do not smoke or allow flames or

sparks where fuel is refueled or
stored.

• Set the fuel tank securely so that it

does not move or fall down while
cruising.

• Position the fuel tank so the tank

fuel line connector is no more than
1 m (3.3 feet) below the outboard
motor fuel line connector.

• Do not place the fuel tank more

than 2 m (6.6 feet) away from the
outboard motor.

• Be sure that the fuel line is not

kinked.

1. Remove the hose plug from the

engine side fuel hose. Insert the
fuel line joint in the engine side
fuel hose and secure it with the
hose clamp. Make sure the arrow
mark on the priming bulb points
toward the engine side.

• Store the hose plug in a secure

place.

(Fuel Tank equipped type)

HOSE PLUG

FUEL TUBE
ASSEMBLY

FUEL HOSE

HOSE
CLAMP

FUEL
LINE
JOINT

(outboard motor side)

FUEL HOSE

(outboard
motor side)

BARB

HOSE CLAMP

(stainless steel)

PRIMING BULB

ARROW

<;DQQMࡍ࡯ࠫ㧞㧜㧝㧟ᐕ㧝㧜᦬㧝㧤ᣣޓ㊄ᦐᣣޓඦᓟ㧞ᤨ㧟㧟ಽ

Содержание BF100A















































































































































































Результаты поиска

Содержание BF100A

Отзывы:

Бренды по названию

Популярные бренды

Honda BF100A, Руководство пользователя

Результаты поиска

Содержание BF100A

Отзывы:

Бренды по названию

Популярные бренды