manualshive.com logo in svg

Honda BF100A, Руководство пользователя

Поделиться
Скачать
Honda BF100A Скачать руководство пользователя страница 28

27

CONTROLS AND FEATURES (R type)

Shifting gear into forward, reverse, or 
neutral and the engine speed 
adjustment can be performed with the 
remote control lever.

It is necessary to pull up the neutral 
release lever to operate the remote 
control lever.

FORWARD:
Moving the lever to the FORWARD 
position (i.e. approximately 35° from 
the NEUTRAL position) engages the 
gear into forward. Moving the lever 
further from the FORWARD position 
will increase the throttle opening and 
the boat forward speed.

NEUTRAL:

Engine power is cut off from the 
propeller.

REVERSE:

Moving the lever to the REVERSE 
position (i.e. approximately 35° from 
the NEUTRAL position) engages the 
gear into reverse. Moving the lever 
further from the REVERSE position 
will increase the throttle opening and 
the boat reverse speed.

Remote Control Lever (R2 type)

REMOTE CONTROL LEVER

NEUTRAL RELEASE LEVER

FORWARD

NEUTRAL

REVERSE

THROTTLE OPENING

THROTTLE OPENING

NEUTRAL

FORWARD

REVERSE

35°

35°

SHIFT

SHIFT

MINIMUM

MINIMUM

MAXIMUM

REMOTE CONTROL LEVER

MAXIMUM

<;DQQMࡍ࡯ࠫ㧞㧜㧝㧟ᐕ㧝㧜᦬㧝㧤ᣣޓ㊄ᦐᣣޓඦᓟ㧞ᤨ㧟㧟ಽ

Содержание BF100A















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды