Honda BF100A Скачать руководство пользователя страница 10

Страница: 10 / 174

SAFETY

• Know how to stop the engine

quickly in case of emergency.
Understand the use of all controls.

• Do not exceed the boat

manufacturer’s power
recommendation, and be sure that
the outboard motor is properly
mounted.

• Never permit anyone to operate the

outboard motor without proper
instruction.

• Before operating the outboard

motor, familiarize yourself with all
laws and regulations relating to
boating and the use of outboard
motors.

• Do not attempt to modify the

outboard motor.

• Always wear a life-jacket when on

board.

• Do not operate the outboard motor

without the engine cover. Exposed
moving parts can cause injury.

• Do not remove any guards, labels,

shields, covers or safety devices;
they are installed for your safety.

• Stop the engine immediately if

anyone falls overboard.

• Do not run the engine while the

boat is near anyone in the water.

• Attach the emergency stop switch

lanyard securely to the operator.

• Shift to the neutral position

and then shift to the reverse
position at low engine speed.

Do not shift to the reverse
position suddenly at high engine
speed.

• Moving parts can injure

you. Install the engine

cover after emergency

starting the engine. Do not
operate the outboard motor
without the engine cover.

<;DQQMࡍ࡯ࠫ㧞㧜㧝㧟ᐕ㧝㧜᦬㧝㧤ᣣޓ㊄ᦐᣣޓඦᓟ㧞ᤨ㧟㧟ಽ

Содержание BF100A















































































































































































Результаты поиска

Содержание BF100A

Отзывы:

Бренды по названию

Популярные бренды

Honda BF100A, Руководство пользователя

Результаты поиска

Содержание BF100A

Отзывы:

Бренды по названию

Популярные бренды