Hofmann geodyna optima Скачать руководство пользователя страница 41

Страница: 41 / 62

E383
Outer scanner not calibrated

Possible causes:

•

the outer scanner has not been factory
calibrated

Corrective actions:

•

please call service and replace the outer

scanner.

E384

Outer motor current sink or power supply failure

Possible causes:

•

the cable connecting the camera controller
board and the outer scanner motor is
unplugged, damaged or missing

•

the motor power supply is not configured
properly

•

there is a fault in the motor power supply board

•

the cable connecting the mains supply and the
motor power supply board is unplugged,
damaged or missing

•

there is a fault in the outer scanner motor

•

there is a fault in the camera controller board
motor drivers

Corrective actions:

•

check all items above.

E385
Outer scanner zero mark not detected

Possible causes:

•

the flat cable connecting the camera controller
board and the outer scanner CCD board is
unplugged, missing or damaged

•

there is a fault in the outer scanner CCD board

•

the outer scanner is locked

•

the outer scanner zero mark is missing, bent,
locked or damaged

•

the cable connecting the camera controller
board and the outer scanner motor is
unplugged, damaged or missing

•

there is a fault in the motor power supply board

•

there is a fault in the outer scanner motor

•

there is a fault in the camera controller board
motor drivers

Corrective actions:

•

check all items above.

Содержание geodyna optima































































Результаты поиска

Содержание geodyna optima

Отзывы:

Hofmann geodyna optima, Дополнительные инструкции, Страница: 41 / 62

Результаты поиска

Содержание geodyna optima

Отзывы: