HNP Mikrosysteme mzr-2521 Скачать руководство пользователя страница 23

Страница: 23 / 92

4 Description of the micro annular gear pump

Operating manual mzr-2521 and mzr-2921

Last update: June 2019

Technical data subject to change without prior notice!

cap nut

casing

seal
O-ring

Ø 1,5x1 mm

fluid connection

figure 11

Pump after installation with both gaskets (version M2)

In order to prevent foreign bodies from penetrating into the pump, the liquid

inlet and outlet are protected by plastic plugs or screws.

Warning

It has to be taken care the packaging of the O-rings that these sit in the

scheduled groove properly. At not proper location of the O-rings the fluid

terminal connection can be or get leaky.

Warning

Tighten the cap nut only hand screwed!

Too firm tightening of the cap nut can rotate to one the pump housing to

lead. The pump can block.

Содержание mzr-2521





























































































Результаты поиска

Содержание mzr-2521

Отзывы:

Похожие инструкции для mzr-2521

Бренды по названию

Популярные бренды

HNP Mikrosysteme mzr-2521, Руководство по эксплуатации

Результаты поиска

Содержание mzr-2521

Отзывы:

Похожие инструкции для mzr-2521

Бренды по названию

Популярные бренды