HNP Mikrosysteme mzr-2521 Скачать руководство пользователя страница 39

Страница: 39 / 92

6 System integration

Operating manual mzr-2521 and mzr-2921

Last update: June 2019

Technical data subject to change without prior notice!

Remarks:

−

It is possible to adjust speed of the micro annular gear pump with the

potentiometer without the need to connect the serial interface.

−

With the analog nominal value input (connection clamps »AnIN« and »GND«)

it is possible to adjust speed of the pump with a standard signal 0-10°V. For

this purpose it is necessary to plug the jumper on the S-ND control unit from

the »AnalogPoti« to the »AnalogExtern«. The serial interface does not need to

be connected.

−

In case of an overcurrent error the green status LED on the S-ND control unit

turns red

−

The standard programs memorized in the motor control unit may be started

with the tumbler switch S1. Basic sample programs are shown in the

chapter 7. For more advanced programs please refer to the user manual for

Motion Controller MCDC3006.

Startup of the pump with the S-ND control units with network mode (NET1

Command)

All standard units are delivered with node number 0. In order to prepare the units

for network operation, they must first be individually connected to the PC and set

to the desired node address using the FAULHABER Motion Manager.

A serial network can be constructed using the so-called daisy-chain technique, in

which the transmit cable of the Master (PC, PLC) is connected to the receive cable

of the first node, from where it is looped through to the receive cable of the

second node, and so on. The same procedure is followed with the receive cable

of the Master, which is looped through to all transmit cables of the drive node.

The current generation of Motion Controllers do not require a multiplexer board

for serial network operation. The multiplex mode is activated with a command

NET1.

S-ND 1

S-ND 2

Controller 1

Controller 2

RS-232 connection cable
article no. 92002801

zero modem cable with
internal resistor

figure 23

Connection between PC, controller S-ND 1 and Controller S-ND 2

Содержание mzr-2521





























































































Результаты поиска

Содержание mzr-2521

Отзывы:

Похожие инструкции для mzr-2521

Бренды по названию

Популярные бренды

HNP Mikrosysteme mzr-2521, Руководство по эксплуатации

Результаты поиска

Содержание mzr-2521

Отзывы:

Похожие инструкции для mzr-2521

Бренды по названию

Популярные бренды