HNP Mikrosysteme mzr-2521 Скачать руководство пользователя страница 16

Страница: 16 / 92

2 Safety instructions

Operating manual mzr-2521 and mzr-2921

Technical data subject to change without prior notice!

Last update: June 2019

2.7

Improper modes of operation

The safety of operation of the delivered device can only be insured by correct use,

as described in chapter 1. The limit values given in this manual must not be

exceeded in any case.

2.8

General safety instructions

Please observe the following safety instructions

The pump may operate at high pressures. For this reason please use only the

delivered accessories and ensure that the employed fittings and tubing have

been prescribed and approved for these pressures.

In order to decrease the pressure, provide the system with a pressure control

valve directing the excess liquid to the initial tank or back onto the suction

side.

At a standstill, the liquid may flow through the pump in the direction of falling

pressure. In order to avoid this unwanted movement, please integrate non-

return valves (see accessories). This applies also to elevated liquid containers.

Protect the micro annular gear pump and the electric drive against strokes and

shocks.

Under normal working conditions the shaft sealing rings integrated in the

pump prevent the liquid from leaking out of the device. The micro annual gear

pumps are "technically leak-proof" however not "hermetically sealed" which

means it may occur that gases or liquids enter to or escape from the pump.

The allowed electrical parameters of the drive must not be exceeded. In

particular an incorrect polarity setting of the supply voltage may lead to

damage of the control unit.

Warning

Please insure, that the totality of the liquid supply accessories such as tubes,

hoses, filters etc. are absolutely free from dust or dirt particles. Impurities such

as metal swarf, plastic or glass splinters may impair or damage the pump

leading to its failure.

Warning

Please, operate the pump with a filter featuring 10 µm or smaller pores. It will

protect the pump.

Содержание mzr-2521





























































































Результаты поиска

Содержание mzr-2521

Отзывы:

Бренды по названию

Популярные бренды

HNP Mikrosysteme mzr-2521, Руководство по эксплуатации

Результаты поиска

Содержание mzr-2521

Отзывы:

Бренды по названию

Популярные бренды