manualshive.com logo in svg

HNP Mikrosysteme mzr-2521, Руководство по эксплуатации

Поделиться
Скачать
HNP Mikrosysteme mzr-2521 Скачать руководство пользователя страница 37

6  System integration 

Operating manual mzr-2521 and mzr-2921 

Last update: June 2019 

Technical data subject to change without prior notice!

 

31 

 

6.5

 

Operation with the S-ND control unit 

The micro annular gear pumps mzr-2521 and mzr-2921 may optionally be 

delivered with the S-ND control unit. This programmable control unit enables to 

adjust speed for constant flow rates or the position of the motor for the dosage 

of constant amounts of liquid. On the delivered diskettes or CDs you will find a 

PC-program operating under Windows that enables to program such parameters 

as speed, acceleration and current consumption. The delivery package comprises 

also a null-modem cable for connection to a serial interface of a PC. 

S-ND control unit 

 

 

 

Type of control unit 

 

4-Q servo amplifier 

 

Nominal voltage 

U 

24 

V 

Power supply 

U

B

 

12 - 30 

V 

Residual ripple 

 

≤

 2 % 

 

Max. continuous output current 

I

continuous

 

230*) 

mA 

Max. peak output current 

I

max

 

400*) 

mA 

Speed range 

 

10...6000*) 

rpm 

Input No. 1 

input resistance 

5 

k

Ω

 

Nominal analog speed 

voltage range 

±

 10 

V 

Nominal digital speed 

PWM signal 

low 0...0.5 / high 4...30 

V 

 

frequency range 

100...2000 

Hz 

Output/Input No. 2 

Error state 

max. U

B

 / 30 mA 

 

 

no error 

switched to GND 

 

 

programmed as input 

low 0...0.5 / high 3,5... U

B

 

V 

Input No. 3, 4, 5 

TTL - logic level 

low 0...0.5 / high 3,5...30 

V 

 

PLC - logic level 

low 0...7 / high 12,5...30 

V 

Program memory 

 

6,6 

kBytes 

*) Values limited in the control unit with corresponding software 

table 15 

Technical data of the S-ND control unit 

The control unit permits an easy startup of the pump with: 

−

 

the possibility to connect the voltage supply to the delivered DIN socket  

−

 

the possibility to connect the voltage supply with screw clamps 

−

 

a 10-pole connector assembly for the motor cable 

−

 

speed set with potentiometer 

−

 

analog voltage signal 0-10 V for speed control at the screw clamps 

−

 

9-pole connection plug for the RS-232 interface 

−

 

error output with status LED, programmable also as trigger input with screw 

connections 

−

 

tumbler switch S1 for the connection of digital input No. 3 of the motor 

control unit 

−

 

screw clamps for the connection of digital inputs No. 3, 4, 5 of the motor 

control unit 

Содержание mzr-2521





























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды