HKS EVC-S Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 39

background image

(1) Connect the Solenoid Valve to the Valve Extension Harness.  Pull the Valve Extension Harness and
      the harness connected to the Boost Sensor from the engine compartment into the vehicle's interior.
(2) Connect the Valve Extension Harness and the Boost Sensor to the Control Unit.
(3) Connect the Display Unit to the Control Unit.
(4) Connect the Power Supply Harness.
      Connect the red wire of the Power Supply Harness to a 12V IG (Ignition) using a crimp connector.
         a) Reconnect the negative cable to the battery.
         b) Turn the ignition on to find the 12V IG wire using a voltage meter.
         c) Disconnect the negative cable from the battery.  Connect the ground wire to a good chassis
             ground.

Remove any paint and/or rust from the surface where the ground wire is connected.
(5) Connect the Power Supply Harness to the Control Unit.

3. Wiring

3-1. Installing the Crimp Connectors

Ԙ

Strip about 5mm of wire insulation.

ԙ

Connect another wire to the uncovered portion

by twisting the wires together.

Ԛ

Crimp the twisted wires using a crimp connector.

ԛ

Cover the crimp connector and wires with electrical tape

to insulate.

Strip 5mm of insulation.

Twist wires together.

Crimp the wires using
a crimp connector.

Insulate with electrical tape.

3-2. Wiring

1(5

#

$

5'6

2*
940

.1%-

452

&41

25+

M2C

/#&'+0,#2#0

㧺㧻

Interior

Engine Room

Solenoid Valve

Boost Sensor

Display Unit

Control Unit

㧙㧙

NOTE

Power Supply

Harness

Valve Extension

Harness

«
...
16
17
18
19
20
...
»

Содержание EVC-S








































Отзывы:

Нет отзывов

Похожие инструкции для EVC-S

Бренд: KEENZ Страницы: 24

Бренд: Warren Controls Страницы: 16

Бренд: Caen Страницы: 20

Бренд: HABONIM Страницы: 9

ecomat 100 R 360

Бренд: IFM Electronic Страницы: 16

Ecomot300 AC2630

Бренд: IFM Electronic Страницы: 11

Бренд: IFM Electronic Страницы: 23

Бренд: Parkside Страницы: 86

Бренд: Talgil Страницы: 14

Бренд: Tadao Страницы: 2

Бренд: Daihan Scientific Страницы: 11

Бренд: M-system Страницы: 7

Бренд: D+H Страницы: 12

Бренд: DUCH Страницы: 9

Бренд: EFI Страницы: 55

Бренд: Samson Страницы: 182

Бренд: PMFoundations Страницы: 5

Бренд: Elektrogas Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды