HKS EVC-S Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 39

background image

㧙㧙

2-1. Connecting the Boost Sensor

˴˴࡮

Remove any oil and/or lubricants on or in the

hose and Vacuum filter.

4mm Hose (5cm)

4mm Vacuum Filter

Surge
Tank

Surge
Tank

Disconnect

Fuel
Regulator

4mm Hose (5cm)

4mm Hose

Fuel Regulator

4mm Hose

4-4-4mm
T-fitting

Surge
Tank

4mm Vacuum Filter

Boost Sensor

Fuel
Regulator

4mm Hose

4-4-4mm
T-fitting

Boost Sensor

(1)  Cut the 4mm Hose to 5cm in length and connect
       the cut hose to the 4mm Vacuum Filter as
       illustrated in the diagram.

NOTE

(2) Disconnect the 4mm Hose between the fuel
regulator and surge tank from the surge tank side.

(3) Cut the 4mm Hose to 5cm in length and insert the
T-fitting as illustrated in the diagram.

(4) Connect the T-fitting and 4mm Vacuum Filter using the
remaining 4mm Hose as illustrated in the diagram.

NOTE

࡮

Keep the 4mm Hose to a minimum length.

࡮

Remove any oil and/or lubricants on or in the hose

and vacuum filter.

࡮

Face the Boost Sensor's fitting downward to prevent

any oil and/or water from entering the sensor.

«
...
8
9
10
11
12
...
»

Содержание EVC-S








































Отзывы:

Нет отзывов

Похожие инструкции для EVC-S

Бренд: Panasonic Страницы: 27

Бренд: Panasonic Страницы: 78

Бренд: Panasonic Страницы: 98

Бренд: NAiS Страницы: 173

Бренд: Panasonic Страницы: 2

Бренд: Haldex Страницы: 8

Бренд: Samson Страницы: 2

Бренд: Saftronics Страницы: 13

Бренд: WAREMA Страницы: 112

Бренд: WAGO Страницы: 414

Бренд: V2 Страницы: 48

GECO LUX GECO60

Бренд: GiBiDi Страницы: 48

Бренд: Daikin Страницы: 150

McDonnell & Miller PSE-80 Series

Бренд: Xylem Страницы: 8

Бренд: J+J Страницы: 56

Бренд: Generac Power Systems Страницы: 20

Бренд: Kathrein Страницы: 32

Бренд: Rain Bird Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды