HISEER AS10S/L Скачать руководство пользователя страница 58 | Manualshive

Страница: 58 / 67

background image

57

If there is not enough refrigerant in the system, this is indicated by gas bubbles in the
moisture sight glass .the unit will have poor performance.

If the low refrigerant charge is significant, large bubbles appear in the moisture sight
glass and the suction pressure drops, then the compressor suction superheat will also
be high.

Find the leak and completely drain the system with a refrigerant recovery unit. Carry
out the repair, leak test and then recharge the system.

Note:

After the leak has been repaired, the circuit must be tested, without exceeding the
maximum low-side operating pressure shown on the unit name plate.

The refrigerant must always be recharged in the liquid state into the liquid line.

The refrigerant cylinder must always contain at least 10% of its initial charge.

For the refrigerant quantity per unit, refer to the data on the unit name plate.

Verify the Alarm Status

1.

Check the alarm menu when the unit is in the standby mode to see if any alarms or
warning have occurred.

Electrical Maintenance

1.

Check for correct termination tension of the electrical connections, contactors,
isolation switch and transformer.

2.

Check the condition of the contactors, fuses and capacitors,

3.

Check the condition of the electrical cables and their insulation.

4.

Carry out an operating test of tray de-icing heater, compressor oil heater,
refrigerant valve and expansion device.

5.

Check the phase/earth insulation of the compressors, fans and pumps.

6.

Check the compressor, fan and pump winding status.

Maintenance

«
...
56
57
58
59
60
...
»

Содержание AS10S/L




































































Отзывы:

Нет отзывов

Похожие инструкции для AS10S/L

Бренд: wallas Страницы: 40

Бренд: Jandy Страницы: 96

Бренд: NARVI Страницы: 48

Бренд: B-TEC Страницы: 11

Бренд: Eaton Страницы: 29

AquaMax Eco Expert 21000

Бренд: Oase Страницы: 136

Бренд: YAMADA Страницы: 14

Бренд: Sentiotec Страницы: 72

Бренд: Mr. Heater Страницы: 36

Pacific Hydrostar 2" or 3" Dirty Water Pump...

Бренд: Pacific hydrostar Страницы: 36

CronoBloc BL Series

Бренд: Wilo Страницы: 43

224342 A Series

Бренд: Graco Страницы: 28

Бренд: Olimpia splendid Страницы: 52

Бренд: T.I.P. Страницы: 133

Gusher 30 Series

Бренд: Whale Страницы: 8

Бренд: Pace Страницы: 84

Бренд: Birchmeier Страницы: 10

Hydra-Cell G-25

Бренд: Wanner Engineering Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды