Hiniker DB1474A страница 30 Скачать руководство пользователя | Manualshive

Страница: 30 / 47

background image

TITLE

SOLENOID VALVE REMOVAL,

CLEANING AND REPLACEMENT

WARNING: Disconnect Vehicle Battery
prior to performing this procedure to
avoid electrical shock or burns.

WARNING: Always retract wings fully,
lower the plow to the ground and re-
lieve pressure before removing any

fittings, hoses or caps. Allow the system to

cool  down  before  draining  oil  or  handling
system  components.  Serious  burns  can  re-
sult  from  contact  with  hot  oil.  FAILURE  TO
HEED CAN RESULT IN SERIOUS INJURY OR
DEATH.

1

2

PHOTO NO. 8996A

Disconnect the black wire of the battery power
cable at location 2. Disconnect the red (or red
striped) wire of the battery power cable from the
motor terminal at location 1.

Disconnect electrical supply to solenoid coil that
will be removed. Mark or make a note of the so-
lenoid coil position for reinstallation.

PHOTO NO. 9014

Remove the solenoid valve coil nut with a 3/4”

wrench. Remove coil from cartridge. Remove
the solenoid valve cartridge with a 7/8” deep well
socket.

PHOTO NO. 3748

Check cartridge valve for contamination. Inspect
O-rings for wear or damage. With a soft, probe,
push in plunger on end of valve. It should push
in approx. 1/16” and spring back.

NOTE:

Doing so should dislodge any foreign

material holding valve open.

Replace cartridge valve if plunger will not push
in and spring back. (P/N 25011066).

20 Solenoid Valve Replacement

«
...
28
29
30
31
32
...
»

Содержание DB1474A
















































Отзывы:

Нет отзывов

Похожие инструкции для DB1474A

Бренд: ShoreStation Страницы: 15

Бренд: Patlite Страницы: 38

Бренд: Nalnor Страницы: 8

AXE 320 PULSE smart

Бренд: Alfain Страницы: 13

Бренд: Balluff Страницы: 124

Бренд: DSC Страницы: 4

Бренд: XceedID Страницы: 2

Бренд: Mec Страницы: 48

Бренд: EAE Страницы: 41

Бренд: Cama Страницы: 18

Бренд: Solter Страницы: 16

Бренд: suntouch Страницы: 20

Бренд: GUDEL Страницы: 36

Бренд: morse Страницы: 6

Бренд: Peak Страницы: 41

Бренд: IMS Страницы: 60

POWERMIG 200-4S

Бренд: ims PRO Страницы: 60

SIMATIC ET 200M

Бренд: Siemens Страницы: 242

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды