Hiniker DB1474A страница 34 Скачать руководство пользователя | Manualshive

Страница: 34 / 47

background image

PHOTO NO. 3745

Remove the two bolts from the pump. Gently pull
on the pump to remove it from the end head.
(

NOTE:

DO NOT lose magnet.)

Remove the shaft seal by gently prying it with a
straight slot screwdriver. Discard seal and pump

O-rings and replace with Kit (P/N 25010334).

Remove the coupling attached to the motor by
pulling out with a pencil magnet.

Clean and inspect all machined surfaces for
contamination, distortion, and wear. Inspect the
inlet suction cover and look for cracks and con-
tamination. Inspect the coupling for wear. Re-
place parts as necessary.

INPUT SHAFT

PUMP GEAR TEETH

DWG NO. 3520

IMPORTANT: DO NOT disassemble Pump fur-
ther. There are No serviceable parts in the
Pump.

Turn Pump Input Shaft by hand and visually in-
spect gear teeth through inlet port. Pump should
rotate smoothly and no teeth should be missing
or damaged. Replace entire Pump if damaged or
if Pump turns hard.

COUPLING

MOTOR

ENDHEAD

SHAFT SEAL
(FLUSH)

DWG NO. 3519

Install coupling onto motor shaft. Lubricate the
pump shaft seal with a multi-purpose grease and
install with lip facing away from pump, smooth

end towards pump flush with end head.

PUMP

MOUNTING BOLT

O-RINGS

BOTH SIDES

DWG NO. 3521

Install O-rings into pump cavities. Re-install
pump by guiding the pump input shaft through
the shaft seal and into coupling. Reinstall the two
pump bolts and torque down to 15-18 ft. lbs.

NOTE:

The Pump Input Shaft will be properly

engaged with the Coupler when the Pump Body

is flat against the end head. Do Not use Pump

Mounting Bolts to force the pump against the
end head.

24 Hydraulic Pump Replacement

«
...
32
33
34
35
36
...
»

Содержание DB1474A
















































Отзывы:

Нет отзывов

Похожие инструкции для DB1474A

Бренд: Far Tools Страницы: 24

Бренд: Parkside Страницы: 113

Бренд: IDEATEC Страницы: 32

Бренд: Zepro Страницы: 64

Бренд: AWELCO Страницы: 40

Бренд: Prowise Страницы: 15

RCT-224 Trailer

Бренд: Miller Electric Страницы: 24

Бренд: Kemppi Страницы: 20

Бренд: Elko Страницы: 18

POWER STICK 200K

Бренд: Codinter Страницы: 14

Synchro-Pulse CDT 450 CP38-3

Бренд: WELDING INDUSTRIES Страницы: 62

Бренд: SEW-Eurodrive Страницы: 384

315P AC/DC Digital

Бренд: Jasic Страницы: 37

Бренд: Migatronic Страницы: 36

Multilin DGT Series

Бренд: GE Страницы: 60

Бренд: Duro Dyne Страницы: 20

Бренд: Peak Страницы: 41

Бренд: BMPRO Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды